Battlefleet Galaxy | BFG Ships
Show All Results...
Imperial cruiser modified with two standard storage modules. This variant is used in deep thrusts into enemy sectors. They are able to maintain the offensive for decades at a time.
| Weight | 0.015 kg |
|---|---|
| Dimensions | 10.4 cm |
| Prow | Anvil, Legacy, Wedge, Eagle, Fortress, Shielding Saint, Burning Book, Marder, Snowpiercer, Shunt, Knight, Mech, Gunprow, Bearded Axe, Classic M, Schmal Jaeger M, Grand w/Adaptor (+£0.90), [Marine] Hammerhead w/ Accessories (+£0.90), [Marine] Crusader w/ Accessories |
| Bridge | Bridge M, Pre-imperial half bridge, Pegasus half bridge, Gun platform, Cyclops, Spinal Gun S, Richelieu Turret L, Yamato Turret L, Pipe Organ, Flakturm, Dome L, Heretic Symbol, Wolf, [17] Chimera Bridge, [21] Tsar Bridge, [22] Legacy Bridge, [23] KGV, [24] Marine Pagoda |
| Rear Weapons | Broadside L, Broadside S, Sponson L, Sponson S, Hangar, Flechette, ✓ Slimline Sponson L, ✓ Slimline Sponson S, ✓ Slimline Broadside, ✓ Slimline Hangar, ✓ Slimline Turret, ✓ Slimline Barrage |
| Forward Weapons | Broadside L, Broadside S, Sponson L, Sponson S, Hangar, Flechette, ✓ Slimline Sponson L, ✓ Slimline Sponson S, ✓ Slimline Broadside, ✓ Slimline Hangar, ✓ Slimline Turret, ✓ Slimline Barrage |
| Forebay | Standard, Grand [+£5.80] |
| Rudder | None, Standard M, Marine Rudder M, Crusader Rudder M, Parapet, Missile Pod M |
| Thruster | Imperial, Twin Engine, Heretic |
Manufacturer:
Manufacturer in the sense of the General Product Safety Regulation (GPSR): Battlefleet Galaxy
Manufacturer address: Unit 4, 9 Crossley Street, Halifax, HX1 1UG, United Kingdom
Manufacturer email: support@battlefleetgalaxy.com
EU Representative (GPSR):
EU representative for the General Product Safety Regulation (GPSR): Simon Saier
EU representative address: Bichler Str. 4a, 82377 Penzberg, Germany
EU representative email: eu@battlefleetgalaxy.com
This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light.
Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave “scars” on the model. These are production-related and do not represent a defect in the product.
Support structure might still remain on the model and can be removed with a sharp hobby knife.
Resin dust is a health hazard if inhaled into the lungs. Grinding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper.
It’s possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty.
Resin heat-sensitive and can therefore deform during the printing process, during the removal of the support structures or during curing. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position.
Important notice
Warning! Not for children under the age of 3. Choking hazard due to small parts.
This product is not a toy.
