The Heretic Battleship is the logical progression of the cruiser, featuring a wider chassis and additional weapon attachment points.
Credit: You can commission the painter Rich on Instagram
Ship Length: 10.5cm (4.1″)
Set includes the following:
Can be shipped by Large Envelope
| Weight | 0.025 kg |
|---|---|
| Dimensions | 10.5 cm |
| Prow | [01] Broadleif, [02] Jaeger, [03] Grand, [04] Marder, [06] Malice |
| Rear Weapon | [01] Hangar, [02] ICBM Launcher, [04] Plasma Turret, [06] Triple Broadside, [07] XL Sponson, [08] Flak Turret, [09] Octa Turret [09] |
| Mid Weapon | [01] Hangar, [02] ICBM Launcher, [04] Plasma Turret, [06] Triple Broadside, [07] XL Sponson, [08] Flak Turret, [09] Octa Turret [09] |
| Front Weapon | [01] Hangar, [02] ICBM Launcher, [04] Plasma Turret, [06] Triple Broadside, [07] XL Sponson, [08] Flak Turret, [09] Octa Turret [09] |
| Rear Bridge | [01] Pre-Imperial Half Bridge, [03] Turret Platform, [04] Nagato, [04] Skull, [05] Eagle Gun, [05] Hooded Angel, [06] Flakturm Tower, [07] Dome M, [07] Lion Standing, [08] Pipe Organ, [08] Invigil Symbol, Spinal Gun S, [12] Pegasus Half-Bridge, [13] Heretic Symbol, [14] Mech Tower, [14] Eye of Behelit, [15] Bridge M, [15] Wolf, [17] Chimera Bridge, [18] Asymmetric Crane Bridge, [20] Cyclops Full Bridge, [21] Tsar Bridge, [22] Legacy Bridge, [23] KGV |
| Front Bridge | [01] Pre-Imperial Half Bridge, [03] Turret Platform, [04] Nagato, [04] Skull, [05] Eagle Gun, [05] Hooded Angel, [06] Flakturm Tower, [07] Dome M, [07] Lion Standing, [08] Pipe Organ, [08] Invigil Symbol, Spinal Gun S, [12] Pegasus Half-Bridge, [13] Heretic Symbol, [14] Mech Tower, [14] Eye of Behelit, [15] Bridge M, [15] Wolf, [17] Chimera Bridge, [18] Asymmetric Crane Bridge, [20] Cyclops Full Bridge, [21] Tsar Bridge, [22] Legacy Bridge & Cantilever Richelieu, [23] KGV |
| Rear Armour | Curved, Plating, Gothic |
| Optional | None, Ramming Shield (+£3.50) |
Manufacturer:
Battlefleet Galaxy
Unit 4, 9 Crossley Street, Halifax, HX1 1UG, UK
support@battlefleetgalaxy.com
EU Representative (GPSR):
Tabletop-Stuff – Simon Saier
Bichler Str. 4a, 82377 Penzberg, Germany
info@tabletop-stuff.de
This is a 3D printed product made of UV hardened resin. Models are cleaned and completely cured with UV light.
Before printing, a support structure needs to be added to the models, these are normally removed after printing, but leave “scars” on the model. These are production-related and do not represent a defect in the product.
Support structure might still remain on the model and can be removed with a sharp hobby knife.
Resin dust is a health hazard if inhaled into the lungs. Grinding and filing is not recommended. Otherwise, such work should only be carried out with appropriate protective equipment (fine dust mask) and/or wet sandpaper.
It’s possible that the models are hollow. In this case, the model has drainage holes through which the liquid resin could leak out. The inside of the model was then also cured. Drainage holes can be closed with modelling putty.
Resin heat-sensitive and can therefore deform during the printing process, during the removal of the support structures or during curing. Hot water or a heat gun/hair dryer can quickly remedy this. The affected part is heated and then carefully bent into the correct position.
Important notice
Warning! Not for children under the age of 3. Choking hazard due to small parts.
This product is not a toy.
